The GearMate Small SteadyBin easily attaches to the medium bracket, keeping your smaller bike accessories—like watches, gels, or charging equipment—secure, safe, and ready for use.
Note: The GearMate Small Bin Kit requires the SteadySpine, sold separately.
Customise your gear, your way with the GearMate Small Bin Kit. Sliding onto the medium bracket, the small bin can store your cycling gear all in one place, making bike storage simple.
SteadyBin: 1 x Small Bin
SteadyBracket: 1 x Medium Bracket
The GearMate Small Bin Kit works by attaching to the GearMate SteadySpine using the medium bracket. The small bin then slides onto the bracket and the grub screws can be tightened to secure the bin in place.
Important: The GearMate SteadySpine is included with the ProFlex Range. For Classic Range installation, the SteadySpine will need to be purchased separately.
JOIN WAITLISTProvide us your email. We’ll contact you when this item becomes available again.
READY TO RIDE
Customise your GearMate, your way.
Easy Storage
GearMate Small Bin Kit
Keep your essentials secure and organised with the GearMate Small Bin Kit. Perfect for storing your cables and other small items, so nothing goes missing when you're on the move.
Common Questions
스테디랙에 자전거를 걸어도 프레임, 포크 또는 바퀴가 손상되지 않습니다. 자전거 프레임의 어떤 부분도 랙에 닿지 않고 강철 암에 고정된 앞 타이어만 닿습니다.
No, you can load and unload the bike at any angle provided that the central pivot bar nuts are set to the factory setting of 5nM.
No, it's not possible to lock the rack solid in one position. You can tighten the nuts sufficiently that the rack will be very hard to pivot which will effectively hold it in the one position. To do this you need to remove the 2 plastic mounting bracket covers (end caps) and tightening the 2 nuts that attach the central pivot bar to the mounting brackets. We recommend you check your fixings to your wall carefully and make sure they are very secure if you do this as any pressure sideways will put extreme pressure on the mounting brackets fixings.
It really depends on the width of your handlebars and the pedals. It will fold until the handlebars touch the wall but not quite 90 degrees or flat to the wall. For a normal road bike bar, we would allow about 400mm or around 16 inches, and for a MTB with wider bars probably around 1m or 39 inches (give or take).
The Fender Racks will suit exactly the same bikes as the Classic Rack except the Fender rack will also work with bikes that have fenders or mudguards, whereas the Classic is only suitable for bikes without fenders and mudguards. The Fender rack will also only accommodate for bikes up to 25kg/55lbs.
One of the main features of our design is the fact that it is the most suitable rack for carbon wheels. There is less pressure on the bike than riding it and it is certainly better than hooks. The wheel is cradled between the two V-shaped cradling points created when the arms are folded down and the tire cushions the wheel and bike. There should be absolutely no need to do any maintenance on your rims or wheels if you use a Steadyrack.
Steadyracks are actually the perfect solution for storing carbon frame bikes and wheelsets! This is because our racks cradle the whole front wheel tire, meaning there is no direct contact with the wheelset or bike frame. Additionally, there is less risk of damage from and to surrounding bikes as the racks are made to pivot and are hung by rolling the bike into the cradle instead of lifting the bike onto a hook.
Yes! This is a common concern for many bike owners with these types of brakes and suspension. When your bike is hung up vertically, the fluid in your forks will run towards the seals and keep them lubricated. This will prolong their use, so it's actually good for your bike and forks to hang it vertically on our bike racks. If you have hydraulic brakes on your bike the fluid will run down when the bike is hung, so we advise pumping the brakes a few times when you take the bike off the rack if it's been there for a while. The shocks shouldn't leak when the bike is hung up, however if they do it's a good indication that the seals may need replacing. Read our blog post for more information about storing bikes with hydraulic brakes in Steadyracks.
Steadyrack 자전거 랙과 함께 뒷바퀴 브래킷/받침대를 설치하는 것이 좋지만 상황에 따라 설치가 제한되는 경우 랙은 여전히 필요에 따라 작동합니다. 나머지 바퀴 없이 뒷바퀴가 평소보다 더 많이 움직이는 것을 발견할 수 있지만 이것이 반드시 필요한 것은 아닙니다.
